Solar Window Film With Heat Rejection

"Where there is demand, there is a market. With a significant increase in demand for films, more and more film brands are entering the market, but the quality and service quality vary. There are many methods for selecting film quality that can be used for reference, but selecting a good film does not necessarily mean that your film selection process has been completed. Note that" three parts of the film and seven parts of the film ", and the final effect of film placement is linked to construction.". So, let's take a look at the details that we need to pay attention to during film acceptance. Don't be fooled by inadequate construction.

1. Whether the construction protection measures are in place. As you should know, many parts such as car parts and lines cannot soak in water or have water seepage. However, during the construction of car film, it is inevitable to use water. If the protective measures are not in place, or the amount of water sprayed from the watering can is too large, there will be water ingress, line failure, and other phenomena. Therefore, excellent construction stores will do a good job of protecting detailed parts and adopt the method of micro water film coating to avoid similar situations.

2. Cutting and baking during the film application process may cause scratches on the glass, poor film shrinkage, or even glass breakage. Therefore, during acceptance, you should carefully check to see if there are new scratches on the glass and side window adhesive strips. For example, master film application uses gaskets to cut the film to avoid scratches on the glass caused by construction; If glass cracks occur during or within 24 hours after applying the film, it is necessary to find the film store for timely treatment.

3. During film coating construction, a dust-free and dust reduction workshop will be selected because there are floating dust and gravel in the air. If dust enters between the film and glass, small bubbles will appear, which will cause trouble for later driving and affect the overall aesthetics. Therefore, dust reduction measures must be taken before construction. Also, when applying the film to drain water, it should be noted that there should be no blisters. You can observe from the left and right sides of the glass separately.

4. There are also requirements for creases. The front and rear windshields should have no more than one crease (including one), the front bumper should be located at the corners (no more than 10 cm from the edge), the rear bumper should be located at the corners (no more than 2 cm from the edge), and the side bumper should have no more than one crease (including one). There should be no creases within the effective range of the wiper.

5. The film should ensure the clarity of driving, so you can sit in the driver's seat and look at the scenery outside the car through the front bumper without blurring or color difference.

6. When lifting and lowering the window, the film on the upper end of the side window is cut flat and straight, and the side window glass cannot leak light when it rises to the top; No light leakage is allowed on both sides of the side window glass (the film is outside the adhesive strip; light leakage occurs when there is light transmission); The edge of the auxiliary window glass is allowed to leak light, but the maximum distance does not exceed 1mm.

7. If you are pasting a metal film, you should also pay attention to whether there are metal false marks on the baking film. The position is generally at the edge (within 15cm from the edge), and the middle position is not allowed.

8. When viewed from a distance of 1 meter from the vehicle, within 10 cm of the partial area behind the glass film, the number of dust points cannot exceed 10.

After selecting a car film, it is not yet complete. You should also pay attention to the final construction effect, so that you do not have to work hard to choose a film that suits your needs. However, due to the substandard level of the film store and technician, your film cannot play its original effect, and even there is a situation of scrapping before it is submitted, which is not worth the loss. It is advisable to carefully inspect the above requirements to avoid being pitted

Are you doing all you can to protect your children and family from window film UV rays?  Are you sure you aren't being bombarded by UV rays window film inside your home without knowing it?  Why not cut UV rays window film 365 days a year?

Reevoo Optics functional films include furniture films, whiteboard films, stealth car coverings, illumination films, and spectrum films to meet different requirements from the users.

Our Value: Health, Happiness, Creativity, Vitality

Our Vision: To establish a flatform of business sharing, to create wealth with our customers, and to help more people as we can.

Hot Tags: solar window film with heat rejection, China solar window film with heat rejection manufacturers, suppliers, factory